Special Project: Silesian Trenchlines part one

Special Project: Silesian Trenchlines part one

---

The Trench Crusade got me my friends. Apart from the allure of the online hype, a lot of my buddies spent the last few weeks entrenched in mud, inviting me in. I gave up and fell victim to their plea for reinforcements. If you follow my blog for a while, you already know that when I get into a game I go all-in, thus here we are – I am making the Trench Crusade gaming board. Now put your helmets on and follow me into the Silesian Trenchline.

---

Usually, when planning a scenery set for miniatures wargaming, I start by making a rough sketch, or set up a provisional board to gauge how much scenery elements feel right. With the Trench Crusade, the community is wildly creative. Scrolling through some amazing examples of gaming boards online I got an idea of how much stuff there should be and how I’d like to approach things. I purchased a few pieces of 50mm thick Styrofoam (XPS foam), a large bottle of PVA glue, 1L of brown acrylic paint, few packages of thin wooden stirring sticks and got to work.

---

---

The core concept of the board was to have it modular, but not limited to square panels. The brilliant idea of creating trenches via stacking walled hills on top of the battlefield really spoke to me thus I went with that. I’m not one to sit down and precisely measure stuff and prefer to work fast and intuitively. The way I do things is cut a single piece of material, then use it as a measuring tool and cut the rest following the lines of the template and a piece of straight board or something currently at hand. I find minor lapse in precision working for the visual benefit and realism of the scenery set. This is what I did, cutting a single 4×4″ triangle and using it as a tool to mark core shapes in XPS. Once done I cut out the shapes with a wallpaper knife.

For the angled sides of the ‘hills’ I marked the top of each piece with a marker, following a previously cut piece of XPS about 1″ wide. This way I had the top of the slope, the supposed bottom being the actual edge of each piece. I then cut, focusing on holding the knife in a steady position and following the imaginable angle between the two lines, not caring if I made any slight errors on the way.

---

---

Once I had a few core shapes I set them up on a 4×4 gaming mat in order to see how the set ‘feels’ and how much I need to add to reach the goal.

---

---

I wanted to have my ‘trenches’ textured with something simple, but effective and look rough. I chose to go with gluing texture on top of the walls with PVA glue. For this I cut old wallpaper alongside a piece of badly damaged transportation paper into strips slightly wider than the height of the ‘walls’. Glued them one at a time on each scenery piece, then upon reaching the second round I used scissors to cut off the excess of the dried out piece, before adding another one beside it.

---

---

I then used a large synthetic brush and sealed everything with a mix of PVA glue and water. Left it to dry afterwards.

---

---

Once the scenery was completely dry, I used a portable gas burner to diversify the texture on top of each piece – done outdoors. I then used PVA glue to mount some roughly cut stirring sticks in semi regular intervals on the sides of the trenches. Finally, using Super Glue, I glued a lot of these 3d printed crosses on each wallpaper covered side, then cut the bottom excess using clippers. This provided a visually interesting setting composition with just enough detail to fit the world of the Trench Crusade, but not too much not to stand out from under the actual scenery.

---

---

The final step for the day was to seal everything again. I mixed water, PVA glue, brown acrylic paint and fine decorative sand then used it to apply texture on top of each piece. I then added a bit more paint and water into the mix and gave the sides a spin. With the help of my valiant daughter we’ve done another round just to build up volume and increase future durability of the scenery.

---

---

The pieces got stacked on top of one another and left to dry through the night, while I sat down to tinker with some extras, mainly walkways, ladders and trench platforms, but I will leave that for the upcoming Special Project: Silesian Trenchlines part two – Peripherals and Extras.

---

I hope you find this article interesting. Be sure to let me know your thoughts in the comments below, or at Facebook or Instagram. I would also appreciate it if you considered sharing this content with your friends, who might find it useful. Finally if you are looking for a professional miniatures painting service, be sure to contact me with this contact form. I always reply within 24 hours, after which please check out your spam folder.